4.buytry-ring-clay-gildflakes-insta
4.buytry-ring-clay-gildflakes-insta

IMG_9885-1000
IMG_9885-1000

IMG_9407-1000
IMG_9407-1000

IMG_9772-1000
IMG_9772-1000

IMG_9794-1000
IMG_9794-1000

IMG_9845-1000
IMG_9845-1000

Hammered Bitsy Rings with Crystal Clay and Gilding Flakes

These Hammered Bitsy Rings with Crystal Clay are super fun and super fast to create! And take a look at how they stack together! Yes please!!!

Get Supplies Read Instructions Be Inspired

Instructions

Super lightweight gilding flakes are perfect for working with Crystal Clay! Slightly wet the tip of a toothpick and pick-up the gilding flakes. Tack the gilding flakes onto the Crystal Clay by gently touching the flakes to the clays wet surface. Gently rub the gilding flakes into the clay with your fingertips.

Read the full instructions.

Supplies Needed:


  • Nunn Design Hammered Bitsy Rings
  • Crystal Clay-Black
  • Gilding Flakes

Other Supplies:

  • 

Rubbing Alcohol
  • Q-Tips
  • Wet-wipes
  • 
Toothpicks
  • 
Business Cards or glossy card stock

Learn How:

Step 1:
The Nunn Design Findings are oxidized to provide the antique look to the precious metal plating. The oxidization, when it comes into contact with the Crystal Clay could change the color of the clay. To avoid this, clean the findings thoroughly prior to applying the clay. Get the tip of a Q-Tip wet with rubbing alcohol and clean away any of the blackened oxidization on both sizes of the Hammered Bitsy Rings.


Step 2:
Follow the manufacturer’s instructions for the handling and mixing of the black Crystal Clay. Crystal Clay is epoxy clay that air-dries. It sets in 2 hours and continues to cure 14-16 hours. There is no baking required, no shrinkage.


Step 3:
While wearing gloves, pinch off two equal sized balls of Part A and Part B and blend together fully until the clay is no longer marbled and uniform in color. You have approximately 90-120 minutes of working time before the clay starts to harden, so take your time. Once the clay is thoroughly mixed, remove your gloves to make it easier to work with the clay. For this tutorial, I mixed a small lentil sized ball of both Part A and B of clay.

TIP: If the Crystal Clay is really sticking, let it sit for 15 minutes. This will allow the fresh clay to have time to set-up a little bit, resulting in it not being as sticky to manage.


Step 4:
Pinch off a very small ball of clay and roll it into a smooth ball using the palm of your hand and fingers. It will take time to get just the right amount of clay that you will need insert into the Hammered Bitsy Ring bezel, so be patient if you have to remove excess clay or add more the first time you do this.


Step 5: 
Press the small smooth round ball of clay into the ring bezel with your fingertips. On the Hammered Bitsy Drop and Triangle Rings, use a toothpick to push the Crystal Clay into the corners of the bezel.


Step 6:
Wipe your hands thoroughly with a wet-wipe. Wipe away any excess Crystal Clay from the ring bezel (if any is on it). The Crystal Clay will harden like cement, so it is best to make sure that any area that you don’t want clay is clean.


Step 7:
If you have finger prints in your clay, or if you want the surface to be smoother than you have it, wet your fingers slightly with water and rub the Crystal Clay. The water will help smooth the clay.


Step 8: 
Place some Gilding Flake onto your work surface. Wet the end of a toothpick and gently touch the Gilding Flake to pick it up. Place the flake onto the wet Crystal Clay and slightly tack into place.


Step 9: 
Once the Gilding Flake is released from the toothpick, start to rub the flake into the Crystal Clay with your fingertips. The Gilding Flakes tear very easily, but don’t worry. Just continue to adhere it onto the clay until you have your desired effect. Gently rub the Gilding Flakes into the Crystal Clay until it is smooth.


Step 10:

Let the pieces cure. They will set up in 2 hours and will continue to cure for 14-16 hours.


Design Option:

To have a high gloss finish, mix-up a batch of Nunn Design 2-Part Resin and drizzle it onto the surface of the Crystal Clay. Although this is a nice effect, it isn’t required to protect the gilding flakes.

Shop Wholesale Products for Technique

rhtbc7-gb
OD:Band width 1.2mm, Bezel 4.8mm Dia x 2mm
Sign In
rhtbc7-sb
OD:Band width 1.2mm, Bezel 4.8mm Dia x 2mm
Sign In
rhtbc7-ssb
OD:Band width 1.2mm, Bezel 4.8mm Dia x 2mm
Sign In
rhtbd7-gb
OD:Band width 1.2mm, Bezel 6.6 x 4.6 x 2mm
Sign In
rhtbd7-sb
OD:Band width 1.2mm, Bezel 6.6 x 4.6 x 2mm
Sign In
rhtbd7-ssb
OD:Band width 1.2mm, Bezel 6.6 x 4.6 x 2mm
Sign In
rhtbt7-gb
OD:Band width 1.2mm, Bezel 7.3 x 6.3 x 1.7mm
Sign In
rhtbt7-sb
OD:Band width 1.2mm, Bezel 7.3 x 6.3 x 1.7mm
Sign In
rhtbt7-ssb
OD:Band width 1.2mm, Bezel 7.3 x 6.3 x 1.7mm
Sign In

Shop Retail Products for Technique

btrf-rhtbc-gb
OD:Bezel sizes vary
$9.50
|
per 3 pack
btrf-rhtbc-sb
OD:Bezel sizes vary
$9.50
|
per 3 pack
btrf-rhtbc-ssb
OD:Bezel sizes vary
$9.50
|
per 3 pack
btrt-cryclay-25blk
OD:25 grams
$10.00
|
ea
btrt-cryclay-50blk
OD:50 grams
$15.00
|
ea
btrt-gf-cb
OD:200ml
$7.99
|
ea
btrt-gf-gb
OD:200ml
$7.99
|
ea
btrt-gf-sb
OD:200ml
$7.99
|
ea

Be Inspired