[everest_gallery alias=”tutorial_sculpted-relief-resin-mold-open-bezel”]

Sculpted Relief Resin Mold within an Open Bezel

Learn this technique from this tutorial below!

Get Supplies Read Instructions Be Inspired

Video Tutorial

Here is a video tutorial we did with Artbeads.com on this technique!

Instructions

Supplies Needed:
Nunn Design Open Frame Bezels
Easy Mold Silicone Putty
Brass Metal Stamping
Nunn Design 2-Part Resin Kit
Castin’ Craft Opaque Pigments
PearlEx Mica Powder

Tools Needed:
Q-tip
Wetwipes
Toothpicks
Business Cards

Read the full instructions.

Learn How!

Make the Silicone Mold

Step 1:
Select a Nunn Design Brass Stamping or a found object such as the fossil I am using in this tutorial. Brass Stampings or found objects with a lot of relief make the best sculpted relief molds.


Step 2:
Pinch off two equal sized balls of Part A and B of the Easy Mold Silicone Putty. Getting the knack for mixing just the right amount of putty will take some practice. You might mix too much or too little putty the first time. Try your best to guess how much putty you will need to have approximately 1/8” putty around the outside edge of your bezel’s rim. You will also want the thickness of the silicone putty to be approximately ¼”.

DSC_0752_1000x1000


Step 3:
The Easy Mold Silicone Putty has a 3-minute working time before it begins to harden and not take the impression. Knead both part A and part B together until the putty is blended completely and has a uniform color.

DSC_0758_1000x1000


Step 4:
Roll the fully mixed Easy Mold Silicone Putty into a round ball and flatten slightly. Make sure the putty is smooth and not wrinkled. Press your brass stamping or found object into the silicone putty, but not so far into the putty that you hit the bottom.

DSC_0762_1000x1000 DSC_0767_1000x1000 DSC_0771_1000x1000 DSC_0776_1000x1000


Step 5:
Quickly remove the brass stamping or found object and press in your Open Back Bezel in a position that frames the brass stamping impression. Be sure to double check that your bezel is level in the mold. Let the Easy Mold Silicone Putty set for 25 minutes. Tip: To prevent your mold from sticking onto your work surface, use a glossy business card or a Ziploc bag.

DSC_0779_1000x1000 DSC_0781_1000x1000 DSC_0786_1000x1000


Mixing and Colorizing the Nunn Design 2-Part Resin

Step 6:
Read the resin instructions for safety concerns regarding the Nunn Design Resin.
When I work with resin, I always:

  • Place a large plastic bag over my work surface and tape it down.
  • I make sure I have ventilation in my workroom.
  • I wear gloves.
  • I wear glasses (readers because I can’t see anymore. Plus it protects my eyes!).
  • I have a pile of wet wipes handy.
  • This is a great blog post that covers 20 Habits for Successfully Using Nunn Design 2-Part Epoxy Resin. Even if you are a seasoned resin mixer, this might be worth a read.

Step 7:
Place one cup (included in the Nunn Design Resin Kit) onto your table. For curing purposes, it is very important that the resin be an exact 1 to 1 ratio of Part A and Part B. I suggest getting your eyes level with the resin so you can see the lines on the measuring cup. Pour Part A of your resin kit up to the ½ fluid ounce mark on your measuring cup.

4-pourpartA_0790-500x500

Pour Part B of your resin kit into the same cup until it is filled to the 1 fluid ounce mark.

5-pourpartB_0806-500x500


Step 8:

Set your timer for 2 minutes. Using the stir stick from your kit (a popsicle stick or coffee stir stick will work great too), slowly and carefully stir your resin scraping the sides as you stir. Stir for a minimum of 2 minutes. If your resin is still cloudy continue to mix until clear. After mixing is complete and your resin is clear, scrape both sides of your stir stick on the edge of your resin filled cup.

6-stirresin2min_0825-500x500

Set the mixture under a warm lamp for 5 minutes. This aids the air bubbles in the resin to rise to the surface and pop.

8-placeunderlamp_0846-500x500


Step 9:
After your resin has been under the lamp for 5 minutes, pour a small amount of the mixed resin into a second measuring cup. Add in a toothpick tip worth of the Castin’ Craft Opaque Pigment Yellow and Castin’ Craft Opaque Pigment Blue to create the teal color show here. You can mix the full 1 fluid ounce measuring cup of resin if you want, but I transfer the resin into smaller cups because it is easier to stir and less messy to move around when less full. Tip: Be sure that the colorant does not equal more than 10% of your resin as having more than 10% could cause issues with curing!

DSC_0836_1000x1000 DSC_0845_1000x1000


Pour Mixed Resin into the Silicone Mold

Step 10:
Using a Q-Tip, rub some PearlEx Mica Powder into the crevices of the silicone mold. Place back into the mold the Open Back Bezel before pouring in the colorized resin. Using your stir stick, drizzle the colorized resin into the bezel. Before the bezel is filled to the flush level of the bezel, take a toothpick and gently move around the resin to see if there are any air bubbles trapped in your mold or along the edge of the bezel. If any air bubbles are within the resin, they will rise to the surface from the agitation. Move the bubbles to the edges to pop, or breathe on them. The hot air from your breath will make the air expand and the bubble will pop.

DSC_0861_1000x1000 DSC_0872_1000x1000 DSC_0877_1000x1000


Step 11:
Let your resin cure for 24 hours. Once cured, slightly bend back the edges of the silicone mold to release the resin and bezel.

Important Information! This technique is ideal for the Nunn Design Open Bezel Deep Channels and the Open Frame Pendants in our product line.  Because these bezel pieces are machined from brass and then plated, there are no irregular edges. Cast bezels do work, but the resin can seep out from underneath the rim of the bezel while it is in the mold. This causes additional clean up, but does look great!


Design Option:


Here is an example of the same technique, but the item was pressed into the molding putty on step 4 was not recessed, it was raised. The impression was created with a vintage button and provided a great relief to the sculpted resin. The Nunn Design Resin was also not colorized nor was PearlEx Powders rubbed into the silicone mold. It was all 100% natural.

Shop Wholesale Products for Technique

Be Inspired