Texturizing and Colorizing Epoxy Clay Tutorial + Video!
This week we will be opening up our latest Buy & Try so that you may explore the technique of texturizing epoxy clay and then colorizing it with 2 part resin and colorants. It is a super fun technique that produces unique results that are truly handmade and of artisan quality.
Shop Wholesale: Buy & Try Texturizing and Colorizing Epoxy Clay
Texturizing and Colorizing Epoxy Clay Tutorial
Designer: Becky Nunn
Bezels, Rings or Button Bezels
Epoxy Clay-Crystal Clay
Clay Squisher Texturizing Pads
Nunn Design 2-Part Resin
Castin’ Craft Colorants
Toothpicks or headpins
Business cards or card stock
TEXTURIZING THE EPOXY CLAY
Follow the manufacturer’s instructions for the handling and mixing of the Epoxy Clay-Crystal Clay. While wearing gloves, pinch off two equal sized balls of Part A and Part B and blend together fully until the clay is no longer marbled and uniform in color. You have approximately 90-120 minutes of working time before the clay starts to harden, so take your time. Once the clay is thoroughly mixed, remove your gloves to make it easier to work with the clay.
Roll the thoroughly mixed Epoxy Clay-Crystal Clay between your palms until it forms a smooth round ball. I like it to be smooth because it prevents from having creases once the impression is made. Press the ball into your bezel, ring, button or flat tag and create an even smooth surface by patting down the clay with your fingers. If you put too much clay in it will squish out the sides and you will have clean up to do. If you don’t put in enough, you might not get a good impression. Regardless, both are easy things to fix, so it might take a little experimenting to get it just right.
Now, let’s make an impression in our epoxy clay. Sprinkle or rub a wee bit of the baby powder over the surface of your Clay Squisher or texturing source. The baby powder will help the clay not stick to your surface.
Place your Epoxy Clay-Crystal Clay filled finding over the texturizing pad and squish down with equal force. I like to pick up the mold and use my fingers to push from the top as well as the bottom to create a good impression.
Using a wet-wipe, clean up any excess Epoxy Clay-Crystal Clay that might have been left on the jewelry finding. The Epoxy Clay-Crystal Clay hardens like cement, so cleaning it up now and being tidy as you go makes the process easier and the results so much nicer. Allow the Epoxy Clay-Crystal Clay to dry for at least 12 hours, well that is what I (Becky Nunn) did, but the staff here at Nunn Design went straight on to pouring the colorized resin on the uncured epoxy clay. Both turned out just fine so use your best judgment!
PREPARING THE COLORIZED RESIN
Preparing the Colorized Resin
Read the resin instructions for safety concerns regarding the Nunn Design Resin.
When I work with resin, I always:
- Place a large plastic bag over my work surface and tape it down.
- I make sure I have ventilation in my workroom.
- I wear gloves.
- I wear glasses (readers because I can’t see anymore. Plus it protects my eyes!).
- I have a pile of wet wipes handy.
- This is a great blog post that covers 20 Habits for Successfully Using Nunn Design 2-Part Epoxy Resin. Even if you are a seasoned resin mixer, this might be worth a read.
- You can also watch this great video on How to Mix Nunn Design Resin
Mixing your resin: Place one cup (included in the Nunn Design Resin Kit) onto your table. For curing purposes, it is very important that the resin be an exact 1 to 1 ratio of Part A and Part B. I suggest getting your eyes level with the resin so you can see the lines on the measuring cup.
Pour Part A of your resin kit up to the ½ fluid ounce mark on your measuring cup.
Pour Part B of your resin kit into the same cup until it is filled to the 1 fluid ounce mark. It is important to pour Part A first and then Part B. It is some chemical thing about the part B being heavier or something.
Set your timer for 2 minutes. Using the stir stick from your kit (a popsicle stick or coffee stir stick will work great too), slowly and carefully stir your resin scraping the sides as you stir. Stir for the full 2 minutes. After 2 minutes, scrape both sides of your stir stick on the edge of your resin filled cup.
Set the mixture under a warm lamp for 5 minutes. I like the lamps with the adjustable arms that can get right down next to the resin. This aids the air bubbles in the resin to rise to the surface and pop.
After your resin has been under the lamp for 5 minutes, pour a small amount of the mixed resin into a measuring cup. Add in a couple drops of the Castin’ Craft Opaque Pigment to give the resin color. I like to use a toothpick or a headpin to add the pigment to the resin. You only need a tiny bit to color the batch. If the resin isn’t as opaque as you would like, add in a drop of the White Opaque Pigment. You can mix the full 1 fluid ounce of resin if you want, but I transfer the resin into smaller cups because it is easier to stir and less messy to move around when less full. To make this tangerine color, I mixed a headpin of yellow and red pigment.
Be sure that the colorant does not equal more than 10% of your resin as having more than 10% could cause issues with curing!
I tend to work in small area (typically my kitchen table), so I like to work on a surface that projects can be easily moved around on and not disturbed. Place some business cards or some heavy card stock onto your work surface, making it easy to move the bezels or tags without getting any resin on your fingers. Lay your bezel or tags onto the business cards, keeping in mind that you will be covering them later with cups to prevent dust for getting on the surface of the uncured colorized resin.
For findings, such as button shanks or ring, use two wood blocks to create a flat surface. I covered mine with packing tape for easy clean up.
Pour the mixed resin onto the epoxy surface you want to colorize. It is best to under pour and then add more if necessary. Using a toothpick or a headpin will allow you to poke it down into the crevices and drag the resin over to the side edges. You can also use the toothpick or headpin to remove excess resin.
Using a wet-wipe, clean off any resin that might be on the sides of the bezel. Let the resin dry for 12-14 hours. It will be dry to the touch, but resin continues to cure over the next 72 hours. I like to put one of the small cups from the resin over the top to prevent from dust getting into the resin as it dries.
Watch our video to learn even more! How To Texturize Epoxy Clay and Apply Colorized Nunn Design Resin.
Shop Supplies RETAIL:
You can explore this technique with our Buy & Try Texturizing & Colorizing Epoxy Clay Program.
Shop Supplies WHOLESALE:
You may also like to read:
- Make This Organic Tag with Crystal Charm Bracelet. Free Tutorial & Video! Kit $18.00!
- Make This Organic Tag With Crystal Charm Necklace. Free Tutorial & Video! Kit $15.00!
- Citrine Point Earrings Video + New Kits by Fusionbeads.com
- July in Review! Get Ready for the Next No Minimum Monday, August 6, 2018!
Welcome to the Nunn Design® Notebook — an online creative space devoted to all that inspires. Here, you’ll discover everything from our latest project videos and Make This how-to guides, to beautiful creations by fellow artisans. Stay current with new product announcements, contests, give-aways, and special discounts. Or learn business tips, tricks, and tools of the trade. Whatever your passion, we hope to help kindle your inspiration, nurture your muse, and unleash your creativity.
All rights reserved © Nunn Design 2017
Would you like to subscribe to our blog? Read 10 reasons why!
Search the Blog
- Adorned Life (17)
- Artisan Spotlight (85)
- Be Inspired (378)
- Becky's Business Tips (6)
- Buy & Try (85)
- Cheatsheets (7)
- Etsy (10)
- Flash Sales (55)
- Getting to know Becky (56)
- Giveaways (110)
- In The Press (59)
- Innovation Team (40)
- Inside Nunn Design (283)
- Kits (27)
- ND Product Info (10)
- Nunn Design Art Retreats (7)
- On My Table (10)
- Product Releases (103)
- Team Nunn (19)
- Tutorials (226)
Buy & Try Products
It is always exciting to see new techniques and projects, but sometimes it takes forever to gather the supplies for that afternoon of creating. The Buy & Try Program allows you to be inspired and purchase just the items needed to explore the technique we are featuring. “Buy & Try” offers may contain items that we don’t typically have in stock! Purchase the “Buy & Try” products either a la-carte, or in a combo pack.
Click on the images below to visit the tutorials and shop the supplies.